Influence of Water Injection on Performance and Emissions of A Direct Injection Jet Ignition Engine

Authors

  • Albert Boretti Department of Mechanical and Aerospace Engineering, Statler College of Engineering and Mineral Resources, Engineering Science Building, 395 Evansdale Dr., P.O. Box 6106, Morgantown, WV 26506-6106
  • Joseph Scalzo Scalzo Automotive Research Pty Ltd, Melbourne, Australia

DOI:

https://doi.org/10.12974/2311-8741.2015.03.01.4

Keywords:

CAE simulations, water injection, turbocharging, jet Ignition, direct injection.

Abstract

A computational model is used to describe the operation of a four cylinder, turbocharged, ignition controlled by spark, direct injection engine fuelled with different fuels, including hydrocarbons, oxygenates and hydrogen. The intercooled engine features port and direct water injection plus jet ignition. The direct water injection permits a further enhanced control of the conditions within the cylinder prior, during and after combustion. Thanks to water injection, a much higher compression ratio is adopted. The port injection of water drastically reduces the temperature of the inlet air, thus permitting more air to enter the cylinder. This translates in more fuel being introduced, for an increased torque and power output. The lower temperature of the air coupled to the direct injection during the compression stroke also improves the resistance to knock, and reduces the heat loss at the walls of the combustion chamber, further improving the fuel conversion efficiency that is already boosted by the use of an higher compression ratio. The enhanced control of the injection of water in the port and the direct injection of fuel in the cylinder is aimed to achieve near to knocking conditions in a stoichiometric mixture about top dead centre that is then ignited almost instantaneously by the jet ignition device. This permits very high fuel conversion efficiencies and high power density during the full load operation. The direct water injection further improves the in-cylinder conditions especially after combustion. Further investigations are needed to better optimise the port and direct water injections. 

References

Rothrock AM, et al. The induction of water to the inlet air as a mean of internal cooling in aircraft engine cylinders. NACA, 1942; report no. 756.

[Cited 2015 Oct 20]: Available from: http://www.rbracing-rsr.com/downloads/naca_H2O.pdf

Brun RJ. End zone water injection as a means of suppressing knock in a spark-ignition engine, NACA 1944; restricted bulletin no. E4127.

[Cited 2015 Oct 20]: Available from: http://www.rbracing-rsr.com/downloads/naca_H2O.pdf

Ladd GT. Water injection for aircraft engines, SAE 1944; P. 460192.

Colwell AT, et al. Alcohol-water injection, SAE 1946; P. 450196.

Eaton DC. Cruising economy by use of water injection, SAE 1946; P. 460198.

Porter JC. Alcohol-water injection for high compression engines. SAE P 1950; 500042.

Nicholls JE, EI-Messiri IA and Newhali HK. Inlet Manifold Water Injection for Control of Nitrogen Oxides — Theory and Experiment, SAE 1969; P. 690018.

Weatherford WD and Quillian RD. Total Cooling of Piston Engines by Direct Water Injection, SAE, 1970; P.700886. http://dx.doi.org/10.4271/700886

Lestz SS, Meyer WE and Colony CM. Emissions from a Direct-Cylinder Water-Injected Spark-Ignition Engine, SAE, 1972; P. 720113. http://dx.doi.org/10.4271/720113

Bratkov AA, Azev VS, Radchenko ED, Gladkikh VA and Livshits SM. Experience In Use Of Water-Fuel Emulsions. Chemistry and Technology of Fuels and Oils 1982; 16(11-12): 731-735.

Tsao KC, Wang CL and Miller EM. Performance Of Gasoline- Water Fuel In A Modified Si Engine, SAE 1984; P. 841399.

Nande AM, Wallner T and Naber J. Influence of water injection on performance and emissions of a direct-injection hydrogen research engine, SAE 2008; P. 2008-01-2377.

Chen R, Chiang L, Wu M and Lin T. Gasoline displacement and NOx reduction in an SI engine by aqueous alcohol injection, Fuel 2010; 89(3): 604-610. http://dx.doi.org/10.1016/j.fuel.2009.07.015

Boretti A. Stoichiometric H2ices With Water Injection. International Journal of Hydrogen Energy 2011; 36: 4469-4473. http://dx.doi.org/10.1016/j.ijhydene.2010.11.117

Boretti A. Stoichiometric H2ice With Water Injection And Exhaust And Coolant Heat Recovery Through Organic Rankine Cycles. International Journal of Hydrogen Energy 2011; 36(19): 12591-12600. http://dx.doi.org/10.1016/j.ijhydene.2011.06.124

Boretti A, Osman A and Aris I. Direct injection of hydrogen, oxygen and water in a novel two stroke engine. International Journal of Hydrogen Energy 2011; 36: 10100-10106. http://dx.doi.org/10.1016/j.ijhydene.2011.05.033

Boretti A. Water Injection In Directly Injected Turbocharged Spark Ignition Engines. Applied Thermal Engineering 2012; 52(1): 62-68. http://dx.doi.org/10.1016/j.applthermaleng.2012.11.016

FEV. Gasoline Combustion Beyond 2020.

[Cited 2015 Oct 20]: Available from: http://spectrum.fev.com/53/en/index.html

Thewes M, Hoppe F, Baumgarten H and Seibel J. Water Injection for Gasoline Combustion Systems. MTZ worldwide 2015; 76(2): 10-15. http://dx.doi.org/10.1007/s38313-014-1012-0

Hoppe F, Thewes M, Baumgarten H and Dohmen J. Water injection for gasoline engines: Potentials, challenges, and solutions. International Journal of Engine Research 2015. http://dx.doi.org/10.1177/1468087415599867

BMW. Innovative water injection system. More power and reduced formation of hazardous substances.

[Cited 2015 Oct 20]: Available from: http://www.m-power.com/_open/s/ varlink2.jsp?id=3301&lang=en

Bulander R. Powertrain optimization using a comprehensive systems approach. Brochure presented to the 2015 36th Vienna Motor Symposium.

[Cited 2015 Oct 20]: Available from: http://www.bosch-presse.de/presseforum/download/ BroschuereA5_Wiener_Motorensymposium_2015_EN.pdf.

Brooke L. Bosch developing new water-injection system for production engines. Automotive Engineering Magazine 2015; 02-Jun.

[Cited 2015 Oct 20]: Available from: articles.sae.org/14176/.

BMW Blog. BMW 1 Series with Direct Water Injection – First Drive.

[Cited 2015 Oct 20]: Available from: http://www. bmwblog.com/2015/07/02/bmw-1-series-with-direct-waterinjection- first-drive/.

Hamori F. Optimising the application of HAJI to the supercharged engine. University of Melbourne 2006, PhD Thesis.

Dober G. Geometric control of HC emissions. The University of Melbourne. 2002, PhD Thesis.

Mehrani P. Predicting knock in a HAJI engine. The University of Melbourne. 2008, PhD Thesis.

Boretti AA, Brear MJ and Watson HC. Experimental and numerical study of a hydrogen fuelled IC engine fitted with the hydrogen assisted jet ignition system, 16th Australasian fluid mechanics conference. Gold Coast. Australia; December 2007.

Boretti A and Watson HC. Development of a direct injection high efficiency liquid phase LPG spark ignition engine. SAE 2009; P. 2009-01-1881.

Boretti A and Watson HC. Development of a direct injection high flexibility CNG/LPG spark ignition engine. SAE 2009; P. 2009-01-1969.

Boretti A, Paudel R and Tempia A. Experimental and computational analysis of the combustion evolution in direct injection spark controlled jet ignition engines fuelled with gaseous fuels. Journal Proceedings of the Institution of Mechanical Engineers. Part D: Journal of Automobile Engineering 2010; 224(9): 1241-1261. http://dx.doi.org/10.1243/09544070JAUTO1465

Douaud AM and Eyzat P. Four-Octane-Number Method for Predicting the Anti-Knock Behavior of Fuels and Engines, SAE 1978; P. 780080.

Heywood JB. Internal Combustion Engine Fundamentals. McGraw-Hill. New York 1988.

Downloads

Published

2015-03-24

How to Cite

Boretti, A., & Scalzo, J. (2015). Influence of Water Injection on Performance and Emissions of A Direct Injection Jet Ignition Engine. Journal of Environmental Science and Engineering Technology, 3(1), 29–35. https://doi.org/10.12974/2311-8741.2015.03.01.4

Issue

Section

Articles