Reinforcement of GFRP Tensile Specimens with Central Holes Using Bonded Composite Patches
DOI:
https://doi.org/10.12974/2311-8717.2023.11.03Keywords:
GFRP tensile specimens, Damage, Composite reinforcement, Bonded Patches, Tensile tests, DelaminationAbstract
The use of bonded composite patches is a promising repair/reinforcement method to extend service live of damaged structures. These patches are non-corroding, lightweight, easy to fabricate and have high specific modulus and strength. In this work, the tensile behavior of a patch-reinforced composite specimen with a central hole is analyzed experimentally. A 10-ply composite tensile specimen is prepared by using bidirectional woven e-glass fabric and epoxy resin as the matrix material. The damage is created in the specimen by drilling three different holes with 3, 6 and 10 mm diameter at the center. The specimen is then reinforced by bonding composite patches or carbon steel patches with different lengths as external patches on both external surfaces. Tensile tests have been carried out on the undamaged, damaged, and repaired specimens. From the tensile tests, it was possible to verify the reduction of the strength (measured by the rupture force) of the specimens with holes of 3 mm, 6 mm and 10 mm. The patches were manufactured using the same glass fiber reinforced plastic, GFRP, used in the specimens or carbon steel. The patches were 25,0 mm wide, 2,5 mm thick. The length was 20 mm, 40 mm or 60 mm. It was found that GFRP patches has better efficiency than carbon steel patches. The repairs with GFRP patches were able to restore between 80% and 90% of the mechanical properties of the intact GFRP specimen without the necessity to replace the composite material.
References
da Costa-Mattos HS, Reis JML, Sampaio RF, Perrut VA. An alternative methodology to repair localized corrosion damage in metallic pipelines with epoxy resins. Mater Des 2009; 30: 3581-91. https://doi.org/10.1016/j.matdes.2009.02.026
Shamsuddoha MD, Mainul Islam MD, Aravinthan T, Manalo A, Lau K. Effectiveness of using fibre-reinforced polymer composites for underwater steel pipeline repairs. Compos Struc 2013; 100: 40-54. https://doi.org/10.1016/j.compstruct.2012.12.019
da Costa Mattos HS, Reis JML, Paim LM, as Silva ML, Amorim FC, Perrut VA. Analysis of a glass fibre reinforced polyurethane composite repair system for corroded pipelines at elevated temperatures. Compos Struc 2014; 114: 117-123. https://doi.org/10.1016/j.compstruct.2014.04.015
Alabtah FG, Mahdi E, Eliyan FF. The use of fiber reinforced polymeric composites in pipelines: A review. Compos Struc 2021; 273: 114595. https://doi.org/10.1016/j.compstruct.2021.114595
Freitas Rachid FB, Costa Mattos HS. Modelling of pipeline integrity taking into account the fluid-structure interaction. International Journal for Numerical Methods in Fluids 1998; 28(2): 337-355. https://doi.org/10.1002/(SICI)1097-0363(19980815)28:2<337::AID-FLD724>3.0.CO;2-6
da Silva ML, da Costa Mattos H. Failure pressure estimations for corroded pipelines. Materials Science Forum 2013; 758: 65-76. https://doi.org/10.4028/www.scientific.net/MSF.758.65
da Costa Mattos HS, Reis JML, Paim LM, da Silva ML, Lopes Junior R, Perrut VA. Failure analysis of corroded pipelines reinforced with composite repair systems. Compos Struc 2016; 59: 223-236. https://doi.org/10.1016/j.engfailanal.2015.10.007
Budhe S, Banea MD, Rohem NRF, Sampaio EM, de Barros S. Failure pressure analysis of composite repair system for wall loss defect of metallic pipelines. Compos Struc 2017; 176: 1013-1019. https://doi.org/10.1016/j.compstruct.2017.06.044
Mahdi E, Eltai E. Development of cost-effective composite repair system for oil/gas pipelines. Compos Struc 2018; 202: 802-806. https://doi.org/10.1016/j.compstruct.2018.04.025
Watanabe Junior MM, Reis JML, da Costa Mattos HS. Polymer-based composite repair system for severely corroded circumferential welds in steel pipes. Eng Failure Analysis 2017; 81: 135-144. https://doi.org/10.1016/j.engfailanal.2017.08.001
da Costa Mattos HS, Reis JML, Amorim FC, Brandao JFS, Lana LDM, Perrut VA. Long-term field performance of a composite pipe repair under constant hydrostatic pressure. Eng. Failure Analysis 2021; 130: 105765. https://doi.org/10.1016/j.engfailanal.2021.105765
Sathler JF, de Luca CR, Reis JML, da Costa Mattos HS. Alternative methods for fracture energy acquisition in the qualification of composite repair system. compos structures 2021; 258: 113420. https://doi.org/10.1016/j.compstruct.2020.113420
De Luca CR, Reis JML, Mota GP, da Costa Mattos HS. Addition of silica in the adhesive primer layer of composite systems used to repair leak defects in metallic pipelines. Composite Structures 2023; 321: 117289. https://doi.org/10.1016/j.compstruct.2023.117289
ASME PCC-2. Repair of pressure equipment and piping, 2022. https: //www.asme.org/codes-standards/find-codes-standards/pcc-2-repair-pressure-equipment-piping
ISO Technical Specification 24817. Petroleum, petrochemical and natural gas industries. Composite repairs for pipework. Qualification and design, installation, testing and inspection, 2015. https: //www.iso.org/standard/59987.html
Reis JML, Costa AR, da Costa Mattos HS. Repair of damage in pipes using bonded GFRP patches. Com João Laredo dos Reis e Alexander Rodrigues Costa. Composite Structures 2022; 296: 115875. https://doi.org/10.1016/j.compstruct.2022.115875
Miranda BM, Reis JML, da Costa Mattos HS. Analysis of the adhesive thickness effect on failure pressure of metal/composite hybrid joints in pressurized blister tests. Com Miranda, B.M., Reis, J.M.L., International Journal of Adhesion and Adhesives 2023; 121: 103314. https://doi.org/10.1016/j.ijadhadh.2022.103314
Baker A. Bonded composite repair of fatigue-cracked primary aircraft structure. Composite Structures 1999; 47: 431-443. https://doi.org/10.1016/S0263-8223(00)00011-8
Zhenhui Sun, Cheng Li, Ying Tie. Experimental and numerical investigations on damage accumulation and energy dissipation of patch-repaired CFRP laminates under repeated impacts. Materials & Design 2021; 202: 109540. https://doi.org/10.1016/j.matdes.2021.109540
FU, Yutong; Yao, Xuefeng; A Review on Manufacturing Defects and Their Detection of Fiber Reinforced Resin Matrix Composites. Composites Part C: Open Access 8 (2022) 100276. https://doi.org/10.1016/j.jcomc.2022.100276
ASTM D3039/D3039M-08 Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials. 2014
Oliveira MJ, Enne FF, Reis JML, da Costa Mattos HS. Alternative surface treatments for the repair of through-wall corrosion damage in metallic pipes with bonded plates, The Journal of Adhesion 2022; 98(16): 2643-2661. https://doi.org/10.1080/00218464.2021.1986395
Green AE, Zerna W. Theoretical Elasticity, London, U, K: Clarendon Press, 1954.
Lekhnitskii G. Anisotropic Plates, translated from the second Russian edition bay, S.W, Tsai and T, Cheron, Gordon. Breach Science Publishers Inc, N4. 3, 1968.
Gay D, Hoa SV, Tsai. SW. Composite Materials. Design and Applications. 1st Edition, CRC Press, Boca Raton, 2002. https://doi.org/10.1201/9781420031683