Optimization of Shrinkage and Mechanical Properties in Continuous Glass Fiber-Reinforced Polypropylene Composite I-Beams during Pultrusion Process
DOI:
https://doi.org/10.12974/2311-8717.2025.13.10Keywords:
Pultrusion process, Shrinkage marks, Nano-SiO₂, Glass fiber mesh, Composite I-beamsAbstract
This study addresses shrinkage marks in pultruded continuous glass fiber-reinforced polypropylene I-beams by modifying the cooling mold with compensation segments, adding nano-SiO₂ as a nucleating agent, and incorporating glass fiber mesh. Under optimized conditions (80 mm/min, 235°C, 65–85–105°C), a compensation segment of 85 mm length and 0.5 mm depth effectively reduced surface shrinkage. Adding 2 wt% nano-SiO₂ lowered vertical shrinkage from 3.07% to 1.15% and horizontal shrinkage from 1.57% to 0.23%. An 8-mesh glass fiber grid further improved dimensional stability while maintaining a bending failure load of 5132.26 N and yield load of 3090 N. These strategies collectively enhance dimensional accuracy and mechanical performance in thermoplastic composite I-beams.
References
Strauß S, Wilhelm F. Development of a Flexible Injection and Impregnation Chamber for Pultrusion of High Reactive Resins. Procedia Manufacturing 2020; 47: 956-61. https://doi.org/10.1016/j.promfg.2020.04.294
Tucci F, Esperto V, Rubino F, Carlone P. Experimental Measurement of the Resistant Load in Injection Pultrusion Processes. Procedia Manufacturing 2020; 47: 148-53. https://doi.org/10.1016/j.promfg.2020.04.157
Nasonov Y, Safonov A, Gusev S, Akhatov I. Effect of Additives on Cure Kinetics of Pultrusion Resins. Procedia Manufacturing 2020; 47: 920-4. https://doi.org/10.1016/j.promfg.2020.04.283
Barkanov E, Akishin P, Miazza NL, Galvez S, Pantelelis N. Experimental validation of thermo-chemical algorithm for a simulation of pultrusion processes. J Phys: Conf Ser 2018; 991: 012009. https://doi.org/10.1088/1742-6596/991/1/012009
Studer J, Dransfeld C, Jauregui Cano J, Keller A, Wink M, Masania K, et al. Effect of fabric architecture, compaction and permeability on through thickness thermoplastic melt impregnation. Composites Part A: Applied Science and Manufacturing 2019; 122: 45-53.
Man Y, Yadong H, Rui L, et al. Melt Impregnation Model of Continuous Fiber Reinforced Thermoplastic Composites. Plastics Science and Technology 2019,47(07): 12-17.
Hopmann C, Wilms E, Beste C, Schneider D, Fischer K, Stender S. Investigation of the influence of melt-impregnation parameters on the morphology of thermoplastic UD-tapes and a method for quantifying the same. Journal of Thermoplastic Composite Materials 2021; 34: 1299-312. https://doi.org/10.1177/0892705719864624
Deng T, Zhang W, Jiang W, Zhou H, Huang Z, Peng X, et al. A hybrid lamination model for simulation of woven fabric reinforced thermoplastic composites solid-state thermo-stamping. Materials & Design 2021; 200: 109419. https://doi.org/10.1016/j.matdes.2020.109419
Shan H, Li M, Guo BB, Zhou XD, Zheng Q, Chen CJ. Influence of process conditions on the mechanical properties of powder-impregnated CF/PEEK prepreg laminates. Aerosp Shanghai 2019; 36: 127-134.
Cui J, Wang S, Wang S, Li G, Wang P, Liang C. The Effects of Strain Rates on Mechanical Properties and Failure Behavior of Long Glass Fiber Reinforced Thermoplastic Composites. Polymers 2019; 11: 2019. https://doi.org/10.3390/polym11122019
Singh AK, Siddhartha. An investigation on the mechanical and thermal performance of a novel functionally graded materials-based thermoplastic composites. Journal of Thermoplastic Composite Materials 2019; 32: 1691-713. https://doi.org/10.1177/0892705718805124
Jing R, Zhang RT, Meng YC, Wang YH, Zhang XG, Zhao Y, Zhang YB. Process parameters in pultrusion of continuous glass fiber/polypropylene thermoplastic composites. Acta Mater Compos Sin 2020; 37: 2782-2788.
Chen K, Jia M, Hua S, Xue P. Optimization of initiator and activator for reactive thermoplastic pultrusion. J Polym Res 2019; 26: 40. https://doi.org/10.1007/s10965-019-1708-6
Zheng CH, Zhou GM, Dong WF, Wang Y, Cao R. Study on bending performance of 3D five-directional braided composite I-beam. Fiber Glass 2014; 39-45.
Asl ME, Niezrecki C, Sherwood J, Avitabile P. Similitude Analysis of Composite I-Beams with Application to Subcomponent Testing of Wind Turbine Blades. Experimental and Applied Mechanics, Volume 4. 1st ed., New York: River Publishers; 2025, p. 115-26. https://doi.org/10.1007/978-3-319-22449-7_14
Goswami R, Murty CVR. Externally Reinforced Welded I-Beam-to-Box-Column Seismic Connection. J Eng Mech 2010; 136: 23-30. https://doi.org/10.1061/(ASCE)0733-9399(2010)136:1(23)
Rudakov IA. Problem on Periodic Vibrations of an I-beamwith Clamped Endpoint in the Resonance Case. Diff Equat 2020; 56: 330-9. https://doi.org/10.1134/S0012266120030064
Li DX. Research on high-performance glass fiber reinforced composite I-beam. Southwest Univ Sci Technol 2019.
Zhang S. Study on mechanical properties of GFRP and concrete composite beam with grid. Harbin Eng Univ 2017.
Yi QS, Zhong YF, Peng X. Reconstruction of three-dimensional local fields in FRP laminated I-beam based on variational asymptotic method. Proc 29th Natl Conf Struct Eng 2020; 219-222.
Lacki P, Derlatka A, Winowiecka J. Analysis of the composite I-beam reinforced with PU foam with the addition of chopped glass fiber. Composite Structures 2019; 218: 60-70. https://doi.org/10.1016/j.compstruct.2019.03.036
Hai ND, Mutsuyoshi H, Asamoto S, Matsui T. Structural behavior of hybrid FRP composite I-beam. Construction and Building Materials 2010; 24: 956-69. https://doi.org/10.1016/j.conbuildmat.2009.11.022
